NAD C 700 V2

• Read these instructions – Read all safety and operating instructions before operating the unit.
• Retain these instructions – Keep the safety and operating instructions for future reference.
• Heed all warnings – Follow all warnings on the unit and in the operating instructions.
• Follow all instructions – Follow all operating instructions and all other instructions provided.
• Cleaning – Unplug the unit from the AC power outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Clean only with a damp cloth.
• Attachments – Use only attachments and accessories recommended by the manufacturer to avoid potential hazards.
• Water and moisture – Do not use this unit near water or in locations exposed to excessive moisture.
• Accessories – Do not place this unit on an unstable cart, stand, tripod, bracket, or table. If the unit falls, it may cause serious injury and severe damage to the unit. Use only a cart, stand, tripod, bracket, or table recommended by the manufacturer or sold with the unit. Mount the unit only as instructed by the manufacturer and use only mounting accessories recommended by the manufacturer.
• Cart – A unit and cart combination should be moved with care. Sudden stops, excessive force, and uneven surfaces may cause the unit and cart combination to tip over.
• Ventilation – The openings in the enclosure are provided for ventilation to ensure reliable operation and protect the unit from overheating. These openings must not be blocked or covered. Never block the ventilation openings by placing the unit on a bed, sofa, rug, or similar surface. Do not install the unit in a bookcase, cabinet, or enclosed space unless proper ventilation is provided or the manufacturer's instructions have been followed.
• Power sources – This product must be operated only from the type of power source indicated on the rating label and connected to a properly grounded AC outlet. If you are unsure of your local power supply, consult your dealer or local power company.
• Power cord protection – Route power cords so they are not likely to be walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit the unit.
• Power plug – If the mains plug or an appliance coupler is used as the disconnect device, it must remain readily operable.
• Outdoor antenna grounding – If an outside antenna or cable system is connected to the unit, ensure that the antenna or cable system is properly grounded to provide protection against voltage surges and static charges. Article 810 of the National Electrical Code (ANSI/NFPA 70) provides information regarding proper grounding of the antenna mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, the size of grounding conductors, the location of the antenna discharge unit, connection to grounding electrodes, and the requirements for the grounding electrode.
• Lightning – For added protection during a lightning storm, or when the unit is left unattended and unused for long periods, unplug it from the AC outlet and disconnect the antenna or cable system. This will help prevent damage from lightning and power-line surges.
• Power lines – An outside antenna system must not be located near overhead power lines or other electric light or power circuits where it could fall into such lines or circuits. When installing an outside antenna system, exercise extreme care to avoid contact with power lines or circuits, as contact with them could be fatal.
• Overloading – Do not overload wall outlets, extension cords, or power strips, as this may result in fire or electric shock.
• Open flames – Do not place open flame sources, such as lighted candles, on the product.
• Object and liquid entry – Never allow objects or liquids to enter the unit through openings, as they may touch dangerous voltage points or short-circuit parts, resulting in fire or electric shock. Do not spill liquids onto the unit.
• Headphones – Excessive sound pressure from earphones or headphones may cause hearing loss.
• Servicing – Unplug the unit from the AC power outlet and refer servicing to qualified service personnel under the following conditions:
  • If the power cord or plug has been damaged.
  • If liquid has been spilled or objects have fallen into the unit.
  • If the unit has been exposed to rain or water.
  • If the unit does not operate normally when the operating instructions are followed. Adjust only those controls covered by the operating instructions, as improper adjustment of other controls may result in damage and often requires extensive work by a qualified technician to restore the unit to normal operation.
  • If the unit has been dropped or otherwise damaged.
  • If the unit exhibits a distinct change in performance, indicating that service is required.
• Replacement parts – Ensure that replacement parts used during servicing are original parts or have the same characteristics as the original parts. Unauthorized substitutions may result in fire, electric shock, or other hazards.
• Battery disposal – Dispose of used batteries in accordance with the applicable local, national, or regional regulations and environmental requirements.
• Safety check – Upon completion of any service or repairs, ask the service technician to perform safety checks to verify that the unit is in proper operating condition.
• Wall or ceiling mounting – Mount the unit to a wall or ceiling only as recommended by the manufacturer.

INSTALLATION NOTES

To ensure proper ventilation, leave at least the following minimum clearances around the unit (measured from the outermost dimensions, including any projections):

Left and right: 10 cm
Rear: 10 cm
Top: 10 cm

FCC STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, as set out in Part 15 of the US Federal Communications Commission (FCC) regulations. These limits are designed to provide reasonable protection against harmful interference in residential installations. This equipment generates, uses and may radiate radio frequency energy and, if not installed and operated in accordance with the instructions, may cause harmful interference to radio communications. However, it cannot be completely ruled out that such interference may occur in some installations. If this equipment does cause harmful interference to radio or television reception (which can be determined by switching the equipment off and on), the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for assistance.

CAUTION

• Changes or modifications to this equipment not expressly approved by NAD Electronics could void the user's authority to operate the equipment.
• This device complies with Part 15 of the FCC Rules and with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
  1. This device may not cause harmful interference; and
  2. This device must accept any interference received, including interference that may cause undesired operation.
• This device complies with the IC radiation exposure limits for an uncontrolled environment.
• Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lower) gain approved by Industry Canada for the transmitter. To reduce potential radio interference to other users, the antenna type and its gain should be selected so that the equivalent isotropically radiated power (EIRP) is not greater than that necessary for successful communication.
• To prevent electric shock, match the wide blade of the plug to the wide slot of the outlet and insert it fully.
• The marking label and rating label are located on the bottom of the unit.
• To reduce the risk of fire or electric shock, do not expose this equipment to rain or moisture. The apparatus shall not be exposed to dripping or splashing, and no objects filled with liquids, such as vases, shall be placed on the apparatus.
• The mains plug is used as the disconnect device and shall remain readily operable during intended use. To completely disconnect the apparatus from the mains supply, unplug the mains plug completely from the AC outlet.
• Batteries shall not be exposed to excessive heat such as sunshine, fire, or the like.
• Danger of explosion if the battery is incorrectly replaced. Replace only with the same or an equivalent type.
• The battery shall not be subjected to excessively high or low temperatures or low air pressure at high altitude during use, storage, or transportation.
• Replacing a battery with an incorrect type may result in an explosion or the leakage of flammable liquid or gas.
• Disposing of a battery in fire, placing it in a hot oven, or mechanically crushing or cutting it may result in an explosion.
• Leaving a battery in an environment with extremely high temperatures may result in an explosion or the leakage of flammable liquid or gas.
• A battery subjected to extremely low air pressure may explode or leak flammable liquid or gas.
• An apparatus with a protective earthing terminal shall be connected to a mains outlet with a protective earthing connection.
• Operation in the 5150–5250 MHz frequency band is restricted to indoor use only to reduce the potential for harmful interference to co-channel mobile satellite systems.

MPE REMINDER

This equipment complies with the FCC RF radiation exposure limits set forth for an uncontrolled environment. To comply with FCC/IC RF exposure requirements, a minimum separation distance of 20 cm (8 inches) must be maintained between the antenna of this device and all persons during operation. Operation at a distance closer than this is not recommended.

IF IN DOUBT, CONSULT A QUALIFIED ELECTRICIAN